In Windows 7, trying to do backup, getting error code 0x8078002A

Anonymous
2011-02-13T19:17:33+00:00

when I try backing up with a system image, using windows7 professional.  Backing up to WD 3TB usb drive I get error code 0x8078002A

Windows for home | Previous Windows versions | Windows update

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments
Answer accepted by question author
Anonymous
2013-03-25T11:37:49+00:00

I had this problem, too, with Windows 7, trying to use Windows Backup to two new Western Digitial 3TB drives, pre-formatted with NTFS for Windows. It's very frustrating because each attempt takes many hours before the error occurs so you don't know until it succeeds whether it will.

I found what worked for me here:

http://wdc.custhelp.com/app/answers/detail/a_id/6618/

You can download WD Quick Formatter from that site. However, don't follow the instructions on that page for formatting a HD under Windows 7, because it tells you how to use MS Disk Management, which will make a 2TB partition and not recognize the remainder of the drive. You must use WD Quick Formatter as described here:

http://wdc.custhelp.com/app/answers/detail/search/1/a_id/3868

Good luck!

[I think it's unconscionable that MS hasn't fixed this with their built-in tools.]

Was this answer helpful?

20+ people found this answer helpful.
0 comments
Answer accepted by question author
Anonymous
2011-12-04T15:47:34+00:00

Hello David JJones,

 If you have followed the steps within this thread but are still having a problem, I would suggest reposting this as a new question at the link below.  Please include any steps you have tried and any additional information that will be helpful.

Microsoft Answers:

http://answers.microsoft.com/en-us/windows

Also, I would suggest looking through the thread below. 

Microsoft TechNet Forum:  http://answers.microsoft.com/en-us/windows

http://social.technet.microsoft.com/Forums/en/w7itprogeneral/thread/d5937704-da8c-44b3-87ef-8d6ad25e0e17

Was this answer helpful?

2 people found this answer helpful.
0 comments
Answer accepted by question author
Anonymous
2011-02-14T21:33:29+00:00

Google provides quite a number of cases involving the same problem you are experiencing. None seemed to be resolved. A number refer to USB external drives.

My research has led me to the two sites mentioned below. On the Petri site I found the quotes extracted as they may point to a possible solution.

Are you using an Enterprise or Ultimate version of Windows as these include Bit Locker Drive Encryption

As a general recommendation in regard to using Windows 7 as a client operating system, use either internal hard disks, separate from the one Windows is installed on. Alternatively, use an external USB hard disk and make sure you disconnect it after you perform your backup.

You cannot use any of the following destinations:

•The destination is locked by BitLocker Drive Encryption.

Source:http://www.petri.co.il/where-to-save-your-windows-7-backup.htm

http://www.sevenforums.com/tutorials/4681-bitlocker-drive-encryption-windows-7-drive-turn-off-no-tpm.html

If the above does not solve the problem can you tell me what security software and firewall you are using as these have proved to cause problems for System Restore in the past?

Hope this helps, Gerry Cornell

Was this answer helpful?

1 person found this answer helpful.
0 comments

97 additional answers

Sort by: Most helpful
Most helpful Newest Oldest
  1. Anonymous
    2012-07-13T16:02:45+00:00

    THIS IS BULLSH**

    I buy a brand new HP laptop with windows 7 pro and spend my time and energy doing windows updates then go to back everything up once I have it tweaked the way I like it, so I make my system repair disk, then go to create an image and

    BOOM

    error 0x8007045D

    THANKS MICROSOFT for releasing BAD SOFTWARE for THE MOST CRITICAL TASK I require BACKING UP MY SYSTEM

    so I start again with an entirely different BRAND NEW hitachi external drive and

    BOOM

    error 0x8078002A

    another example of Windows 7 Pro worthlessness in CRITICAL areas...

    YES, I ran the steps outlined above, same issue

    YES, I would like to be able to use this drive with my older Windows XP system, so

    NO, I will not reformat my entire external drive to a smaller 512byte size.

    FIX THE PROBLEM MICROSOFT and quit having your techs make it sound like it is a vendor issue by running UNNECESSARY TROUBLESHOOTING STEPS...

    Was this answer helpful?

    0 comments
  2. Anonymous
    2012-06-22T00:21:57+00:00

    This applies to Seagate, WD, etc.. There is a problem in WIndows that causes Windows backup to fail. Here is a response I got from the "horses mouth" so to speak when I slammed their 3TB drives in a review....

    "This reply is from Seagate Support. We noticed your review and wanted to comment on your experience with your Backup Plus for Mac 3TB drive. There is a limitation within the Microsoft operating system that prevents Windows Backup from working properly on drives larger then 2TB at this time. "

    So if you are using a 3TB drive for backup, you should purchase backup software that guarantees that it can backup drives larger than 2TB. Seagate has a product called Memeo that is bundled with GoFlex drives. I can't recommend the product. I've encountered this SW several times and have had to abandon it each time. So plan on purchasing a better product.

    Was this answer helpful?

    0 comments