Linx 1020 tablet will not work after Windows Update

Anonymous

Yesterday evening I updated my Linx 1020 tablet via Windows Update. Three updates were downloaded and installed, which I have listed below. (N.B. for the benefit of Microsoft Support my Link 1020 came pre-installed with Windows 10 and is still under manufacturer's warranty)

1) Update for Windows Defender

2) Cumulative Update for Windows 10

3) Insyde Firmware update (this required a restart)

After Windows downloaded and installed the updates I was required to restart so I opted to update and reboot. My Linx 1020 shut down normally and the Linx logo display as it started to reboot. However, after this point the screen remained black and no matter what I tried I could not start my tablet. The orange power light also does not display when on mains power. Prior to shut down my Linx 1020 was 97% charged and on mains power.

Since yesterday I have tried repeatedly to boot my Linx 1020 to no avail. To all intents and purposes my Linx 1020 is dead and it is my belief that one or more of the Windows updates is responsible for this rather than a fault with my Linx 1020. The most probable culprit is the Insyde Firmware update as this required the restart.

I have read on the LinxTablet.co.uk forum that other Linx tablet owners have experienced a similar issue after performing a Windows Update.

I am waiting for a reply from Exertis (Linx support) regarding this issue but as the evidence clearly points towards an issue with Windows Update I would be grateful for a response from Microsoft Support, setting out how Microsoft intends to help Linx owners resolve this issue.

To reiterate: my Linx 1020 tablet is dead and cannot boot due to a fault with Windows Update!!

Moved from: Windows /Windows 10 /Power on or off a device /PC

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments

70 answers

Anonymous

2018-01-02T12:13:18+00:00

Thanks for the useful information.
Was this answer helpful?

1 person found this answer helpful.

0 comments No comments
Anonymous

2017-10-13T13:41:55+00:00

I did the same ,removed s/d card ,held volume down and power after a lot of stuttering it fired up now seems to be ok. Mike
Was this answer helpful?

1 person found this answer helpful.

0 comments No comments
Anonymous

2017-05-05T09:40:22+00:00

As far as I am aware no official fix has been announced by Microsoft.

However, I heard from a Linx 1020 owner this morning that a compatibility fix may now be included in the latest Windows Update.

Unfortunately for those of us that have already been affected by this issue it is very much a case of being too little too late.

I have left my Linx 1020 unplugged for 18 hours and I have just followed the advice from Exertis (Linx Support) about doing a soft reset and my tablet will simply not even power up. It is dead as a Dodo!

I rather fear you may well have to return you Linx 1020 to the retailer for an exchange or refund; as I shall be doing shortly for the second time in two days!
Was this answer helpful?

0 comments No comments
Anonymous

2017-05-05T09:25:43+00:00

I am having the same issue and it happened after windows update and my new linx 1020 is not booting up, is there a resolution from microsoft ?
Was this answer helpful?

0 comments No comments
Anonymous

2017-05-03T12:58:44+00:00

Hi

Thanks for taking the time to respond.

Unfortunately my tablet will not even power up so somehow creating a USB recovery media would make no difference. I have tried using the USB recovery media I created for my laptop to see if that would at least boot but nothing happens. My tablet is quite literally dead!

I have also checked the power cable and that is working fine.

Thanks again.

Marc
Was this answer helpful?

0 comments No comments