I receive the following stop error when trying to install Windows XP: Stop: 0x0000007B

Anonymous

I need help with this error code: Stop: 0x0000007B (0xF7C85524,0xC0000034, 0x00000000, 0x000000000)

I'm a Microsoft Answers noob. I have an old computer I'm trying to reinstall Windows XP on. It's a Dell XPS Dimension 3 (3.40 gigahertz Intel Pentium 4, 1G RAM). It won't boot normally or in Safe Mode. I have tried using Fixmbr, Fixboot, Bootcfg /rebuild, chkdsk /r, Memtest86, Killdisk. I have tried installing using another hard drive (which leads me to believe it might be a hardware issue). It gave the same error code, I believe, although I didn't write it down. The only thing I've found that I haven't tried is "How to recover from a corrupted registry that prevents Windows XP from starting" since it says that it won't work on OEM devices. The error code is Stop: 0x0000007B (0xF7C85524,0xC0000034, 0x00000000, 0x000000000). I tried installing Ubuntu on both drives and they installed and worked properly. I don't know what else to try except hardware troubleshooting, although I'm not too good with hardware issues. If you have any recommendations that might put me closer to a resolution I would greatly appreciate it!

P.S. Windows XP actually ran on the second hard drive I tried (which is currently the drive in the machine right now). I installed it and it booted straight into Windows. Yay! I rebooted this setup many times with no problems. But I had an issue with Microsoft Security Essentials updating so I thought a clean install would be better. In retrospect I wish I had tried harder to fix that issue but I didn't. The first hard drive incurred a Windows crash that caused me to upgrade to a Windows 7 machine. This was over 1.5 years ago. I just thought the full back story might help.

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments

Answer accepted by question author

Anonymous

I wanted to post this update to help people that may experience this problem in the future. I finally got it to work. After many combinations and permutations, I ended up having a “NTLDR is missing” error message. I used this link

http://tinyempire.com/notes/ntldrismissing.htm

I followed the instructions, made sure I had a version of Windows XP installed on the hard drive [after using Killdisk many times], and changed the boot preference to Drive>SATA operation>RAID Autodetect/ATA. I booted the FixNTLDRiso disk and after the first run rebooted and VOILA! My computer booted into Windows. Yay!!

After installing all the Windows updates its still working like a charm. Hope this helps!!

0 comments

Answer accepted by question author

Anonymous

Hi,

I am close to certain (but experience tells me very little is 100% certain), that a generic windows installation CD will install without the need for F6 diskette, provided that BIOS is set to RAID Autodetect/ATA (or possibly 'combination'). AHCI is a more efficient disk access method but does require F6 diskette or slipstreaming. If the CD is already slipstreamed for your PC, AHCI should work without F6. Given that you say your BIOS defaults to RAID Autodetect/AHCI, I would expect a CD targeted specifically for your system to support this, whereas a generic CD would not.

I doubt that they will provide F6 diskette but you never know. If you don't ask you probably won't get.

You can mark replies in this thread as 'Answers'...

...but if memory serves me correctly you can only mark a maximum of 2 'Answers'. I would suggest my final diagnosis (and maybe my first reply) as candidates but this is entirely at your discretion. You may even want to hold off on marking 'answers' until you get another CD from Dell and try it. This also helps other people who are looking at this thread hoping to find a solution to 7B stops.

You can designate any other replies as helpful if you think that it is approriate.

Tricky

0 comments

Answer accepted by question author

Anonymous

Hi,

Did this PC originally have Vista or Win7 installed?

I have seen the 0x0000007B BSOD caused by trying to install XP to a hard drive whilst BIOS is designating the drive as AHCI instead of IDE. XP does not have native AHCI drivers and the consequence is a 7B stop.

If BIOS is set to AHCI, change the BIOS setting to IDE/ATA.

There are other options but research on the Dell website leads me to suspect that these might prove problematical. Can you confirm whether or not your PC has a floppy disk drive (the Dell picture makes me think it doesn't).

Tricky

0 comments

93 additional answers

Anonymous

2012-06-08T20:43:14+00:00

I was trying to get to a C: prompt is the reason I was using recovery console. I also tried this morning to put in a USB stick in the computer and find it. But I went up to j: and it didn't find it.

Did you boot with the memory stick inserted or did you insert after booting. If the latter then insert the USB stick before booting. Then you should find the files and be able to copy them to the floppy diskette.

Tricky
Was this answer helpful?

0 comments No comments
Anonymous

2012-06-08T20:10:06+00:00

I've already copied the files to a CD btw. And a USB stick

If I may add a little here, the other post are spot on. The 0x07B stop code is the result of not having the SATA controller driver on the Windows disc or it can also result from not having sp2 or sp3. Both scenarios can and will cause the error. I did not nor will I go back through 6 pages of post only to get to the same solution.

My advice is to start over with the slipstreaming.

Also, regarding your above statement, you cannot simply "copy" the files to the disc. You must create a bootable iso image then burn the iso image to the disc. Forget about using a usb stick. That is a very difficult process to get to work with Xp.

First, if your disc does not contain sp3 then download the stand alone version HERE. Save the file to your desktop. Do not run it of course.

Second, download the Intel Matrix storage driver from HERE. Again, save the file to your desktop. Right click in a free space on the desktop and choose Create a new folder. Name it Drivers. Now click on the f6flpy3288 folder you just downloaded and extract the files to the new Drivers folder you created.

Next, create a folder on your desktop and name it Windows XP. Copy the files from your current Windows disc to the Windows Xp folder you created on your desktop.

Now open Nlite. Navigate to the Windows XP folder you just created on your desktop. Nlite will take a second to recognize the Windows XP folder.

Click "Next" until you get to the menu where you select the task to perform. Select "Integrate Service Pack", "Drivers" and "Create a Bootable ISO". Click Next.

You will next click "Select" and navigate to the Service Pack 3 you downloaded and saved to the desktop and select it (Open).

The next screen is where you select the drivers to integrate. Click "Insert" > "Single Driver File". Select "Text Mode Driver". Navigate to the drivers folder you created on your desktop where you saved the drivers you downloaded. While holding down the Ctrl key, left click on each driver one at a time until all are highlighted. Once all are highlighted click Next. You will be prompted if you want to start the process. Of course you select "Yes". The process will begin.

After the process completes the final window will appear. Use the drop down menu under "Mode" to select "Direct Burn". With a blank disc in the cd/dvd drive click "Burn". Allow the process to complete. Boot from the disc and install Windows.
Was this answer helpful?

0 comments No comments