atikmdag.sys, Windows 7 x64, ATI Radeon 4850, Crossfire

Anonymous

I am on my 3rd install of Windows 7. Having a really bad time with the video drivers. And from what I have read, others are too. I shut it off for now and will leave it off till better drivers are released. The funny this is, is that the drivers from windows update are just as bad as the drivers from ATI. If you install the video drivers from windows update you are looking at BSOD. You can reboot into safe mode and remove everything ATI however if you continue to try to boot normally you will ruin the OS and you will have to reinstall. Specifically it is atikmdag.sys. This was also an issue with Vista from what I have seen researching this issue. The supposed work around is to just install the driver but even if you download just the driver it wants to install the Catalyst Control Center which atikmdag.sys is a part of. So you are stuck between wanting to install the drivers for your video card or using the generic video driver that is stable and won't crash your system. The annoying thing is is that with the generic driver the video on the monitor is scaled. So you have a black border all the way around the screen. The maximum resolution of my monitor is 1920x1080. The best I can get with the generic driver is 1440x1080.

I would say that it was a hardware conflict somewhere however this is hardware that worked just fine in Windows XP.

Is there a fix for this yet or is it more of a "be patient" thing?

My system is as follows,

Asus P5K-E Motherboard

4 gigs of DDR2 1066 RAM

3 10,000 drives RAID 0

ATI Radeon 4850 cards in Crossfire. Monitor hooked up via HDMI.

Not that any of that matters since it seems everyone across many different configurations is having the very same issue as I am.

Essentially, its a very expensive case full of hardware that is unusable. I know that I am going to asked for information that I haven't included in this post but I am at work at the moment and can't provide it.

Thanks

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments

Answer accepted by question author

Anonymous

Alright everybody.. Same situation for me. Two HD 4850's in crossfire mode.. I updated some drivers and started to get the BSOD with the atikmdag.sys error. I actually came up with a fix for this 4 hours later that doesn't require you to reformat your computer. In my case, here is exactly what I did:

Start computer in safe mode with networking
Download and install Driver Sweeper which can be obtained here
Start the Driver Sweeper program, check the ATI - Display box and click on the Clean button. This will delete ALL ATI drivers from your system.
Reboot computer again, it should start normally now if everything worked right... Now you're gonna remove any CCC program via add/remove programs.
Now all you have to do is find the original driver you had before you tried to upgrade. I would recommend using the disk that came with your video card. You can also go to the ATI website and search for your exact model and download the drivers... Keep in mind, I would stay away from the newest versions of drivers as they all seem pretty buggy...

The current CCC software I am running stable is: Catalyst™ Control Center Version 2010.0406.2133.36843

The current driver I have installed for my HD 4850's in crossfire mode is atikmpag.sys (8.14.1.6113)

This driver with that version of CCC hasn't failed me yet. Try not updating graphics drivers if you don't have to. If it isn't broke, don't fix it.

I really hope this helps everybody out... I got mine working again... Oh and for all of you with the black borders issue the post above mine is 100% accurate and will fix the issue.

Also this is the system I am currently running:

SPECS:

Microsoft Windows 7 Professional 64-bit

AMD Phenom II X4 965 Black Edition Deneb 3.4GHz Socket AM3 125W Quad-Core Processor

ASUS M4A79XTD EVO AM3 AMD 790X ATX AMD Motherboard

Crucial Ballistix Tracer 6GB (3 x 2GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory

XFX HD-485X-ZNFC Radeon HD 4850 1GB 256-bit DDR3 PCI Express 2.0 x16 x2 in crossfire hooked up via HDMI cable

ASUS VE246H Black 24" 2ms(GTG) HDMI Widescreen LCD Monitor

Seagate Barracuda 7200.11 ST31500341AS 1.5TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive

0 comments

Answer accepted by question author

Anonymous

I had the black border as well but its actually an easy fix and hopefully it'll work for you. Go to your CCC Panel, then go to Graphics, then to Desktops and Displays, then in the bottom left corner, you will see your monitor or monitors. When your mouse is over the icon an arrow pointing downward will appear that will represent a drop down menu. Click that arrow then click Configure. You should see more then several tabs on this screen. Click the tab called Scaling Options, then slide the bar to Overscan (0%) and click apply then ok. You should be good to go. :)

0 comments

41 additional answers

Anonymous

2010-04-05T01:30:42+00:00
You need no special software , I'm proof, using a default windows utility I've finally Solved ! Resolved ! & amazingly.. Fixed ! my windows 7 (64 bit) BSOD blue screen of death issue of a specific phenomenon of the particularly RANDOM system file corruptions ~ i.e. (the ones all over the map)

Like you I have diagnosed all my hardware components, clean installed all my (updated) drivers, clean installed a new operating system, updated from windows update (desperately I tried the (bogus) claims of a registry cleaner (FAIL!). Frustration, denial, anger, grief, & finally acceptance/surrender all the same stages of death. From arghh to *sighh. lol

The causes being; but not limited to : dxgmms1.sys , ntoskrnl.exe , nvlddmkm.sys , ETC. ETC. I had them all reported & chronically for about a month. Well all of those corrupted contributors ARE I'm delighted to say, healthy again!

It's simple : All that needs to be done is 1st open up the command window.

(you'll be initiating microsofts System File Checker)
1. Then type in: sfc /scannow
2. press enter
3. that's all. It will find all currupt system files & replace them with healthy ones. Even if some can't be fixed (like in my case) It should find/replace all the fatal ones. Believe me, I've been ripping my fingernails out rooting out this issue, I'm so relieved. Hope it helps. I should note that all my hardware is diagnosed healthy & configured properly, yours should be too for this to work. Godspeed!
SPECS:

ASUS m4a785-M board

EVGA Nvidia 9800 GTX+ Vcard

Kingston HyperX DDR2 2066 4gb dual chan. tam

AMD AthlonII 2X 240 regor

An assortment 'o Seagate HDD's

sata 16~32 buffers 7200~5900 rpms
Was this answer helpful?

0 comments No comments
Anonymous

2010-03-30T10:02:32+00:00

Hi all,

I suddenly have the same issue running with a 2x4890 Crossfire, the system just even fails to boot up reporting a blue screen with the atikmpag.sys file error. If I remove the crossfire bridge, and the system runs on one graphics card, either of them, it works perfectly. Do you think it has to do with the drivers? The temperatures of the system are very good. Please some advice would much appreciated in case someone has res
Was this answer helpful?

0 comments No comments
Anonymous

2010-03-30T10:01:16+00:00

Hi all,

I suddenly have the same issue running with a 2x4890 Crossfire, the system just even fails to boot up reporting a blue screen with the atikmpag.sys file error. If I remove the crossfire bridge, and the system runs on one graphics card, either of them, it works perfectly. Do you think it has to do with the drivers? The temperatures of the system are very good. Please some advice would much appreciated in case someone has resolved it.

Widows 7 Ultimate 64

Asus P6T

2 x Sapphire Radeon 4890 1gb

Intel Core i7 920
Was this answer helpful?

0 comments No comments