Something happened and your PIN isn't available. Click to set up your PIN again.

Anonymous
2020-07-12T23:16:34+00:00

* * Locked * *

I have a new PC with W10. I decided to use the PIN code, but now I get the message "Something happened and your PIN isn't available. Click to set up your PIN again."

When I click 'Set up my PIN' nothing, the same message reappears.

I looked up the issue on the internet and found that I should login using another sign-in option. However, there is no way to get to another option. The text above is all I see on the screen.

Windows for home | Windows 10 | Windows Hello, lock screen and sign-in

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments
Answer accepted by question author
Anonymous
2020-07-12T23:37:28+00:00

Hello there! I'm sorry that didn't work. You can try this steps instead:

Turn off your PC

Start your PC, just as Windows attempts to load (spinning dots), press and hold Power Button on the casing of your PC for 5 - 10 seconds to perform a Hard Shut Down

Do this twice

On the third start Windows will boot into the Recovery Environment and from there you can access System Repair, Safe Mode, Command Prompt . . . etc.

Please try each option one at a time, then see of Windows will boot . . .

Go to Troubleshoot - Advanced Option - Startup Repair

See if Windows startup can repair itself

Go to Troubleshoot - Advanced Option - System Restore

Check to see if you have a restore point you can go back to

If you do not have a Restore Point, go to Troubleshoot - Advanced Option - Startup Settings and click Restart

Upon restart, press 4 to enter Safe Mode

Once in Safe Mode, backup your data if you do not already have a backup

Open Device Manager and check to make sure all your Drivers are up to date

Reboot to see if Windows will start Normally

If the above fails, go to Troubleshoot - Advanced Options - Reset this PC

Choose to keep your files and apps, just your files or to keep nothing

Then start the Reset

Hope this will do the trick

Regards,

Louie

Was this answer helpful?

1400+ people found this answer helpful.
0 comments

492 additional answers

Sort by: Oldest
Most helpful Newest Oldest
  1. Anonymous
    2021-02-19T21:17:28+00:00

    I have Bitlocker setup and I can't access the pin or the sign in?

    It keeps asking for the Bitlocker key and I don't know it?

    None of the steps you outlined have worked for me?

    I can't even figure out how to get into Safe Mode because

    Bitlocker won't let me? Does anybody have any ideas?

    I can get into the repair screen but none of that works either?

    I can even get into a command line but thats it?

    I need to know how to disable bitlocker and then get into Safe Mode?

    Was this answer helpful?

    0 comments
  2. Anonymous
    2021-02-19T21:21:29+00:00

    thats not true I've tried it and it doesn't work or make any sense?

    Was this answer helpful?

    1 person found this answer helpful.
    0 comments
  3. Anonymous
    2021-02-19T21:51:01+00:00

    Robert,

     first how to get into safe mode.   safe mode is AFTER the screen you get when you hit shift restart.   After Troubleshoot. I can't look at the options right now but I think if you pick  the option above Command Prompt and wait a bit, 10 or so options will come up that you pick by entering their number.    This 10 option screen will show you all the boot options and one of those is safe mode, safe mode is not something you can directly pick after Advanced or Troubleshoot like you do with Command Prompt.  Just a word of warning though, I'm pretty sure safe mode demands a pin too, if you have pin's turned on.

 you and I were in very similar situations with Command Prompt.   I was in Command Prompt and I wanted to change some things that normally I would do in Settings.   Command Prompt is pretty active.  i found I could run taskmgr, regedit, cmd, and notepad from command prompt and they would come up.  You can get some commands by saying "start .... ".  I couldn't run file explorer or Settings.  In cmd you can  run command line.  I just googled bitlocker and there are command line commands for it.   I found that net user (add, modify, delete users) would run while I was in command prompt although I'm not sure the commands were taking affect.  

 Incredible if just a user using bitlocker can lock himself out of his machine.   Microsoft needs to review this and the shut off all services situation.  Good luck.  Keep trying, I found I had to do a lot of trials to get my machine back.

    Was this answer helpful?

    1 person found this answer helpful.
    0 comments
  4. Anonymous
    2021-02-20T19:16:46+00:00

    I tried restoring my pc to the automatic backup file and it worked, thanks for the help

    Was this answer helpful?

    0 comments