PC won't boot to Windows 10 from SSD

Anonymous
2018-08-20T08:11:17+00:00

I bought my PC years ago with only a HDD. I added a SSD myself afterwards. When I booted my PC after a hard shutdown/electricity fallout I had only my HDD in BIOS. I then boot from HDD, get an error and let the PC reboot. After a few times the SSD would be recognized in BIOS and I could change the SSD to default.

I got tired of this proccess a few days ago and found a tip to disable the hdd-partition with diskpart. The first time I had a hardreset again (mouse and keyboard froze and pc didn't shutdown with a single press on startbutton), I couldn't do the HDD boot-trick and tried changing the cables from hdd to ssd (ssd in sata1). This didn't help. In diskpart I made the SSD partition active. I now can see the SSD in BIOS, but booting gives an error "An operating system wasn't found.". When I retry diskpart, the partition could be made active again. It seems like this resets..

Bootrec.exe /FixMbr was successful

Bootrec.exe /FixBoot gives no access error (there could be some parts left of a dual boot setup)

chkdsk gives no problems found

Mediatool boot:

  • This PC can't be recovered with start-uprepair.
  • You need to choose which installation of Windows you would like to put back when using Systemrecovery.
  • Reboot, select a operating system and select Systemrecovery. No systemcopy available.

How could I make my pc boot again?

PC: MEDION AKOYA P5367 D EU (MSN: 10015458)

Motherboard: MS-7728

BIOS version: E7728MLN.209

SSD: Kingston SV200 (128GB)

HDD: ST1509DL003-9V (1500GB)

Windows for home | Windows 10 | Performance and system failures

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments

107 answers

Sort by: Oldest
Most helpful Newest Oldest
  1. Anonymous
    2018-08-20T08:33:47+00:00

    You need a operating system to install to be able get any thing.

    Download the Media Creation Tool and install from there.  Read the instructions.

    Media Creation Tool US;  Read the instructions.   

    Instructions link

    https://www.microsoft.com/en-us/software-download/windows10

    Was this answer helpful?

    1 person found this answer helpful.
    0 comments
  2. Anonymous
    2018-08-20T09:23:35+00:00

    Hi Remco,

    Reading through your post, and it says your PC came with an HDD, and therefore the OS was installed on that drive. When you added the SSD, did you just use it for storage, or did you install the Win 10 OS on it as well?

    Sorry if you mentioned it in there, I didn’t see it if so.

    Let me know and we’ll try to figure this one out!

    • C

    Was this answer helpful?

    0 comments
  3. Anonymous
    2018-08-22T13:03:47+00:00

    Thanks for your reply.

    I installed Windows 7 (upgraded to 10) on the SSD myself.

    Was this answer helpful?

    0 comments
  4. Anonymous
    2018-08-22T13:04:46+00:00

    There is/was an installation of Windows 10 on the SSD. But it won't boot any longer.

    Was this answer helpful?

    1 person found this answer helpful.
    0 comments
  5. Anonymous
    2018-08-22T14:13:51+00:00

    Hi,

    If your HDD was hooked up when you installed Windows to the SSD, there were probably boot files saved to the HDD for the SSD..

    If this is the case, making the OS partition on the HDD "Not Active" or "Hiding" it can cause a boot failure when trying to boot from the SSD...

    It may have also created a Dual Boot setup that can be hard to fix... Not counting the fact that the SSD may have been damaged by the power failure...

    If the SSD is not appearing in Bios, that indicates some type of damage either to the SSD or the motherboard...

    There are two areas in the Bios where you should see the SSD... The area where you select the Boot Device, and another area where you select which HDD\SSD will be on the list for Boot Device.... You might check that one...

    The SSD needs to Be "Active" to be bootable..

    There is another area where your SATA controller\ports are listed, along with info concerning which drives are attached... If the SSD is not listed there, you have a problem..

    I can only suggest that you unhook the HDD temporarily, and then try your Startup\Boot Repair again...

    Are you running DiskPart and the Boot Repair commands from bootable Win 10 installation media ? If not that would be best..

    How you make the media can be important as well... If you should create installation media for a machine with UEFI Bios, it may generate errors when using it on a machine using the older Legacy Bios...

    The commands you are using for "Active", "Not Active" only work on a machine that boots while using Legacy Bios...

    The Boot Commands I use are...

    BOOTREC /FIXMBR

    BOOTREC /FIXBOOT

    BOOTREC /REBUILDBCD

    You might try both the Startup Repair and Boot Commands... Try the Startup Repair, and if it fails, then go to the Command Prompt and try the BootRec stuff.. If that fails, try the Startup Repair again.. It might take several tries... if it will even work...

    BTW... What OS is on the HDD ?

    Was this answer helpful?

    0 comments