Bootsect.dat file is corrupted, NTLDR is missing/compressed on x86 pc with WinXP Home Edition Sp3 and Ie8

Anonymous
2014-02-24T05:47:39+00:00

I have a x86 pc with WinXP Home Edition SP3 and IE8. 

While preparing for an eventual upgrade to Win 7, I have been considering repartioning and multibooting my HDD. 

I have been trying to get WinXP operating as best as I can.  I also have been checking out how to use the Windows Recovery Console to reinstall WinXP and transfer files for a clean reinstall.

I discovered while checking "All Boot Paths" at Start\Run\msconfig\BOOT.INI that one Boot Path was highlighted with errors indicating that the "File is Corrupted because a disk read error occured" and that NTLDR is missing or corrupted.  In fact, it is garbled.  It points to "Microsoft Windows Recovery Console/cmdcon".  I have not used the Recovery Console, ever. 

I have a Gateway 5310S desktop (retail) and no original XP disks, apparently. 

I do have, but have never used, a 4ea. set of Recovery CDs dated 5/12/05 that I must have created after purchase.

I also have been having numerous, odd, problems that come and go, including trouble displaying various websites, Yahoo Home Pages, and eMail that keep going into compatibility mode or blanking outright.  The video and audio on Hulu and online video services are always out of sync.  I have problems editing posts on sites like this even though I can edit my profile pages just fine.

This particular set of problems started occurring recently and very suddenly, from one day to the next.  This was after it had actually been working fairly well for a change. 

I have no idea how long the boot.ini file has been corrupted, I actually discovered it by accident.

I also can not reinstall certain programs such as Family Tree Maker 2005 and 2008 after it was suggested to me by ancestry.com to uninstall/reinstall.

I have the latest Java and Adobe Flash Player.  I have defragged and disk checked my drives. 

I have used CCleaner to remove temp and junk files daily.  I have run Hitman Pro, MBAM, MBAR, MSE, and SAS multiple times with no viruses or malware detected. 

And, as I had mentioned above, I am having problems with the editor on this site, right now.  Sometimes it just freezes and I have to exit to clear.  Other times it duplicates entire sentences.  It also flip/flops between a full page editor and, like now, a half page editor window on the left half of the page.

Any suggestions you folks can come up with would be greatly appreciated.  This is getting really annoying.

Thanks

Vernon

Windows for home | Previous Windows versions | Performance and system failures

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments
Answer accepted by question author
Anonymous
2014-03-05T08:10:47+00:00

when you check out the boot.ini paths, and the recovery console is installed, you will always get an error stating that the boot path is invalid.

if the recovery console is indeed corrupted just uninstall, you can reinstall or burn a cd with the recovery console.

go here for instructions on deleting the recovery console.

===========

Here's how to make a bootable xp recovery console cd

Courtesy of JoseIbarra

You need to start by booting into the XP Recovery Console using a CD you can make (no XP media required) and run a chkdsk with error correction enough times until it runs clean and if that doesn't work, you can create a new boot.ini file (it is usually one of those two things).

Here's how:

Use the XP Recovery Console to verify the file system on your HDD and correct any problems and then try to boot your system - this may be all you need to do.  Or, you are welcome to just start trying things that might work.

Boot into the Windows Recovery Console using a bootable XP installation CD.

If you have no bootable XP media (or are not sure what you have) create a bootable XP Recovery Console CD and be sure what you have (no XP media required).

This is not the same as any recovery disks that might have come with a store bought system.

You can make a bootable Recovery Console CD by downloading an ISO file and burning it to a CD.

The bootable ISO image file you need to download is called:

rc.iso 

Download the ISO file from here:

http://www.thecomputerparamedic.com/?p=8    (courtesy of Daavee)

Use a new CD and this free and easy program to burn your ISO file and create your bootable CD:

http://www.imgburn.com/

When installing ImgBurn, DO NOT install the Ask toolbar.

Here are some instructions for ImgBurn:

http://forum.imgburn.com/index.php?showtopic=61

It would be a good idea to test your bootable CD on a computer that is working.

You may need to adjust the computer BIOS settings to use the CD ROM drive as the first boot device instead of the hard disk.  These adjustments are made before Windows tries to load.  If you miss it, you will have to reboot the system again.

When you boot on the CD, follow the prompts:

Press any key to boot from CD...

The Windows Setup... will proceed.

Press 'R' to enter the Recovery Console.

Select the installation you want to access (usually  1: C:\WINDOWS)

You may be asked to enter the Administrator password (usually empty).

You should be in the C:\WINDOWS folder.  This is the same as the 

C:\WINDOWS folder you see in explorer.

The Recovery Console allows basic file commands like: copy, rename, replace, delete, cd, chkdsk, fixboot, fixmbr, etc.

For a list of Recovery Console commands, enter help at the prompt or read about the XP Recovery Console here:

http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

A good idea before starting things is to first verify the integrity of your file system using the chkdsk command.

From the command prompt window run the chkdsk command on the drive where Windows is installed to try to repair any problems on the afflicted drive.

Running chkdsk is fine even if it doesn't find any problems.  It will not hurt anything to run it.

Assuming your boot drive is C, run the following command:

chkdsk C: /r

Let chkdsk finish and correct any problems it might find.  

It may take a long time for chkdsk to complete or it may appear to be 'stuck'.  Be patient. If the HDD light is still flashing, chkdsk is doing something.  Keep an eye on the percentage amount to be sure it is still making progress.  It may even appear to go backwards sometimes.

You should run chkdsk /r again until it finds no errors to correct.

Remove the CD and type 'exit' to leave the RC and restart the computer.

You do not have to adjust the BIOS again to boot on the HDD since the CD will not be present.

===============

as for the other problems:

have you used any registry cleaners??

these can harm your system

since you appear to be infection free, it would seem that some part of your cleaning process has deleted a necessary file.

===============

checkdisk with the /r parameter should be run. and run again until no errors are found.

==========

are you fully updated and patched at Microsoft updates??

Was this answer helpful?

0 comments

82 additional answers

Sort by: Oldest
Most helpful Newest Oldest
  1. Anonymous
    2014-04-03T03:49:55+00:00

    Hi Elizabeth23,

    1) I have asked my brother-in-law who is a consultant in the computer industry business along with his sons to try and locate an original WinXP setup disk.  Hopefully they can find one.

    2)   If the disks I originally created at time of first bootup of my system that I then labelled as "Master - RecoveryCD1 (thru 4) Gateway 5310" are the second type you listed above, where do I find a "How-To" manual for using them to fix stuff? 

    All I have is an extremely simplified pamphlet that tells you how to CREATE the disks, but does not explain HOW to apply them.  Note that these are NOT boot disks.  And I have never used them. 

    Thanks

    Vernon

    Was this answer helpful?

    0 comments
  2. Anonymous
    2014-04-03T19:00:20+00:00

    I have been to the gateway site to try to download a pdf manual for your pc, Gateway desktop 5310S PC 4000966, serial number 0035394453

    http://us.gateway.com/gw/en/US/content/contactus

    above is the contact page, maybe they can give you a User's Manual to download for your particular pc.

    Was this answer helpful?

    0 comments
  3. Anonymous
    2014-04-04T05:31:28+00:00

    Hi, Elizabeth23,

    OK, now I have a challenge for you.

    ElderL (and others) have said that to make a bootable repair disk for WinXP you must have the SATA drivers for the harddrive to slipstream into the .iso along with SP3.

    The catch is that the Seagate harddrives do not require drivers, but the SATA controller on the Intel motherboard (Intel D915GAG (J2E1) version 4000966) apparently does.  Seagate doesn't even supply drivers at all.

    I have looked for SATA controller drivers on the Intel site, but found nothing obvious. 

    So, just HOW do I do that?   

    I was actually able to track down an original bootable Windows XP setup disk to even do this, but I guess I still need the drivers?  Catch-22?  Why does all this have to be really frigging hard in the first place?

    Gateway support is non-existant, so I have to seek help elsewhere.

    Any suggestions you have will be welcome.

    Thanks

    Vernon

    Was this answer helpful?

    0 comments
  4. Anonymous
    2014-04-04T07:13:37+00:00

    Was this answer helpful?

    0 comments