100% Disk Usage on Windows 8.1

Anonymous
2014-06-22T07:15:31+00:00

Hello, I'm Leo

I would like to address the problem with windows 8.1, i find that with updating Windows from Windows 8 to 8.1 causes a very concerning problem.

the problem causes the disk usage as show in the task manger to be 100%.

The problem with 100% disk usage causes some problems like:

  • Slows Down Computer
  • Ruins Hard Drive (Over Long term use without FIX)

I've tried to fix it many times, i have used many methods like: 

  • Running Command Prompt
  • Scanning my Files and Hard Drives
  • Restore my PC to Factory Settings

non of these worked and now i have read the post of where u run "services.msc" and disable few services like "Superfetch" or "Windows Services" but i realize that this is not a fix and that when windows tells you to do this it only to make it look like your disk it not 100%, my computer still runs pretty slow (Got my Laptop 3 months ago) and i have not downloaded any third party software cause my network is always at 0% when i have 100% Disk usage.

Conclusion:

Windows 8.1 is the cause of the 100% Disk Usage. Windows 8.1 has a lot more background programs running than windows 8 did this change has caused windows to use up 100% of the disk space

I need help i need someone to help fix this problem

Ps all my files and programs are up to date including my BIOS

Windows for home | Previous Windows versions | Performance and system failures

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments
Answer accepted by question author
Anonymous
2015-03-23T15:41:01+00:00

Hi Joel,

Try the following methods and check if it resolves the issue.

Method 1:

Step 1: Try Safe Mode

Safe mode is the configuration of Windows, when it is running on only basic set of drivers and all the startups are disabled. To know more about safe mode, follow the article below:

http://windows.microsoft.com/en-in/windows-8/windows-startup-settings-safe-mode

If the issue is resolved in safe mode, follow step 2 after restarting the computer in regular mode.

Step 2: Clean Boot

A clean boot is performed to start Windows by using a minimal set of drivers and startup programs. This helps eliminate software conflicts that occur when you install a program or an update or when you run a program in Windows. To know more, follow the article below:

http://support.microsoft.com/kb/929135

Note: After troubleshooting, refer to this section ‘How to reset the computer to start normally after clean boot troubleshooting’.

Method 2: Run a Virus Scan

I would recommend you to run a complete virus scan using the Microsoft Safety Scanner. It will scan the computer for viruses and malicious programs. To download it and know more about it, click on the link below.

http://www.microsoft.com/security/scanner/en-us/default.aspx

Disclaimer: Any data files that are infected may only be cleaned by deleting the file entirely, which means there is a potential for data loss.

Hope this information was helpful.

Was this answer helpful?

70+ people found this answer helpful.
0 comments

130 additional answers

Sort by: Newest
Most helpful Newest Oldest
  1. Anonymous
    2016-09-27T09:34:00+00:00

    Dont rush 

    The same 100%disk usage is on win 10, also no solution 

    .........  I don't know what the f***k should i say

    Was this answer helpful?

    0 comments
  2. Anonymous
    2016-09-27T09:28:47+00:00

    Actually i had the issue too... I uploaded to SSD and my laptop was perfect with same specifications.

    so yes upgrading to SSD will be great idea!

    Was this answer helpful?

    0 comments
  3. Anonymous
    2016-09-27T09:24:01+00:00

    This helped me lower the Disk Usage from 100% to less than 20%! Thank You!

    I implemented this solution and the earlier solutions. none of them seems to work. I can notice that when ever there is internal scan on the hard disk that involves any I/O or for example virus scan from trend micro in my case this issue starts. even with the SuperFetch or other services disabled. this is very sad. I think I am upgrading to 10 and forget to solve this issue in my enterprise. unfortunately there is a lot of work then to be done.

    wondering will this be same even if I change the HDD to SATA SDD?????

    Was this answer helpful?

    0 comments
  4. Deleted

    This answer has been deleted due to a violation of our Code of Conduct. The answer was manually reported or identified through automated detection before action was taken. Please refer to our Code of Conduct for more information.

    Comments have been turned off. Learn more