Event says when my system froze that "The DgiVecp service failed to start due to the following error: The system cannot find the file specified."

Anonymous

I found the exact problem that causes this freezes. My computer freezed today at 20:17. I went to the event viewer and found that at that time there is an event says that "The DgiVecp service failed to start due to the following error: The system cannot find the file specified."

Is there anyone who knows about it?

Thank you.

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments

Answer accepted by question author

Anonymous

Hi, Tekinalp67,

Try Gloria's Suggestion from this thread-

http://answers.microsoft.com/en-us/windows/forum/windows_vista-hardware/error-6008/5a6138d1-e997-4d74-98a4-bb974c4114c1

-Or-

Start > Type Regedit

Press Enter

Navigate to the following key:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services

Look for an entry listed as DgiVecp

If you find this, then change the Start data value to 4.

Reboot the system and see if the message is gone.

http://tzatziki-solvedproblems.blogspot.com/2010/02/dgivecp.html

0 comments

Answer accepted by question author

Anonymous

Event ID 6008 - is it still showing up in Event Viewer? Possibilities were heat, video drivers, faulty devices, failing HD's etc

Event ID: 41 Source: Kernel-Power

Source: Kernel-Power
Type: Critical
Description: <br><br>The last sleep transition was unsuccessful. This error could be caused if the system stopped responding failed or lost power during the sleep transition.<br><br><br> <br><br><br>Check for loose connections - did you change power settings to never?<br><br><br>CPU could be overheating<br><br><br>Driver software could be at fault<br><br><br>http://www.eventid.net/display.asp?eventid=41&eventno=9230&source=Kernel-Power&phase=1<br><br><br> <br><br><br> <br><br><br>Boot your system in a clean boot state. When it is up in a clean boot state, activate the sleep mode process. If it has not problems coming out of sleep mode when in the clean boot state, add a few more services back and try the process again. Continue until<br> the issue occurs, then the issue is probably one of the driver's/services that were last enabled that is conflicting with the process sleep undertakes to place the system in sleep mode.<br> <br><br> <br><br>Here are the steps for clean boot; - I recommend updating all drivers and firmware as a step in resolving this as well. <br><br> <br><br>CLEAN BOOT: you can use the steps in the article to narrow down the cause of the problem,http://support.microsoft.com/kb/929135. <br><br>(Step 1 is listed below.) <br><br>Step 1: Perform a clean boot Note If the computer is connected to a network, network policy settings may prevent you from following these steps. We strongly recommend that you do not use the System Configuration utility to modify the advanced<br> boot options on the computer unless a Microsoft support engineer directs you to do this. Doing this may make the computer unusable.<br><br><ol><br><li>Log on to the computer by using an account that has administrator rights. </li><li>Click <strong>Start<br><div><img src="http://support.microsoft.com/library/images/support/kbgraphics/Public/EN-US/VistaStartButton.jpg"></div><br>, type <span>msconfig.exe</span> in the <strong>Start Search box, and then press ENTER to start the System Configuration Utility.<br><br><br><br><div><img src="http://support.microsoft.com/library/images/support/kbgraphics/Public/EN-US/SecurityShield.jpg"></div><br>If you are prompted for an administrator password or for confirmation, type your password, or click<strong>Continue.<br></strong></strong></strong>Regards,<br><br><br><br></li><li>On the <strong>General tab, click <strong>Selective Startup, and then click to clear the<strong>Load startup items check box. (The<br><strong>Use Original Boot.ini check box is unavailable.)</strong></strong></strong></strong></li><li>On the <strong>Services tab, click to select the <strong>Hide all Microsoft services check box, and then click<strong>Disable all.<br><br><br><br><strong>Note</strong> Following this step lets Microsoft services continue to run. These services include Networking, Plug and Play, Event Logging, Error Reporting, and other services. If you disable these services, you may permanently delete all restore points.<br> Do not do this if you want to use the System Restore utility together with existing restore points.</strong></strong></strong></li><li>Click <strong>OK, and then click <strong>Restart.</strong></strong> </li></ol><br><br>http://answers.microsoft.com/en-us/windows/forum/windows_vista-hardware/cannot-awake-from-sleep/fa423ca9-2412-49b5-9f97-37c43a1419c5

Source: Kernel-Power

Type: Critical

Description: The last sleep transition was unsuccessful. This error could be caused if the system stopped responding failed or lost power during the sleep transition. Check for loose connections - did you change power settings to never? CPU could be overheating Driver software could be at fault http://www.eventid.net/display.asp?eventid=41&eventno=9230&source=Kernel-Power&phase=1 Boot your system in a clean boot state. When it is up in a clean boot state, activate the sleep mode process. If it has not problems coming out of sleep mode when in the clean boot state, add a few more services back and try the process again. Continue until the issue occurs, then the issue is probably one of the driver's/services that were last enabled that is conflicting with the process sleep undertakes to place the system in sleep mode. Here are the steps for clean boot; - I recommend updating all drivers and firmware as a step in resolving this as well. CLEAN BOOT: you can use the steps in the article to narrow down the cause of the problem,http://support.microsoft.com/kb/929135. (Step 1 is listed below.) Step 1: Perform a clean boot Note If the computer is connected to a network, network policy settings may prevent you from following these steps. We strongly recommend that you do not use the System Configuration utility to modify the advanced boot options on the computer unless a Microsoft support engineer directs you to do this. Doing this may make the computer unusable. <ol> <li>Log on to the computer by using an account that has administrator rights. </li><li>Click Start <div><img src="http://support.microsoft.com/library/images/support/kbgraphics/Public/EN-US/VistaStartButton.jpg"></div> , type msconfig.exe in the Start Search box, and then press ENTER to start the System Configuration Utility. <div><img src="http://support.microsoft.com/library/images/support/kbgraphics/Public/EN-US/SecurityShield.jpg"></div> If you are prompted for an administrator password or for confirmation, type your password, or clickContinue. Regards, </li><li>On the General tab, click Selective Startup, and then click to clear theLoad startup items check box. (The Use Original Boot.ini check box is unavailable.)</li><li>On the Services tab, click to select the Hide all Microsoft services check box, and then clickDisable all. Note Following this step lets Microsoft services continue to run. These services include Networking, Plug and Play, Event Logging, Error Reporting, and other services. If you disable these services, you may permanently delete all restore points. Do not do this if you want to use the System Restore utility together with existing restore points.</li><li>Click OK, and then click Restart. </li></ol> http://answers.microsoft.com/en-us/windows/forum/windows_vista-hardware/cannot-awake-from-sleep/fa423ca9-2412-49b5-9f97-37c43a1419c5

0 comments

80 additional answers

Anonymous

2011-12-30T22:55:24+00:00

I found a discussion

http://community.norton.com/t5/Norton-Internet-Security-Norton/Windows-7-Forums-tell-of-a-problem-with-Norton-2011-and-FREEZING/td-p/527496
Was this answer helpful?

0 comments No comments
Anonymous

2011-12-30T22:46:39+00:00

Opps the hotfix is not suitable for me then.

Now only 2.99 gb is usable for 32 bit. Can norton internet security cause this problem?
Was this answer helpful?

0 comments No comments
Anonymous

2011-12-30T22:41:08+00:00

I found a hotfix in microsoft web site. "http://support.microsoft.com/kb/2265716/en-us"

is this ok for me?

According to this document -

This issue occurs because of heavy group policy use and the presence of SCOM causing a deadlock condition between the Lsass.exe process, the Redirected Drive Buffering Subsystem (Rdbss.sys) driver, and the Winsock kernel.

Does that apply to you? Are you (as listed in Symptoms of document)

A computer that is running Windows Server 2008 R2 or Windows 7 with System Center Operations Manager (SCOM) and a large number of GPOs (Group Policies) running a service that calls for Local Security Authority

If these descriptions fit you, then by all means use the hotfix but, if they do not, use it at your own risk.

How much memory are you using and what is the Maximum Ram you're allotted?

Try uninstalling a memory module and see if system hangs with less memory.

Edit: In addition, scroll down to JoselBarra's post on this thread.

http://answers.microsoft.com/en-us/windows/forum/windows_xp-system/pc-keep-getting-bsod-d1-7f-8e-and-freezing-caused/c26f1d00-12be-489e-84fa-f93db00d5668?page=3&tm=1325284937923
Was this answer helpful?

0 comments No comments