Unable to boot - Safe Mode stops after crcdisk.sys

Anonymous
2010-07-11T01:34:05+00:00

original title: Windows Vista 32-bit crashes as system is loading. Safe mode hangs after crcdisk.sys loads.  System restore also fails.

My computer (an HP m9200t) no longer fully boots after installing a new windows update.  When turned on the computer will begin to load windows and allow me sign in.  However, about 30 seconds to 2 minutes after signing in I can no longer interact with my desktop (although I can interact with programs that automatically load upon startup, like windows live messenger).  I sometimes receive a screen that says "kbd.exe failed to initialize properly".  I have tried to restore my system to a point before the update loaded, but I am told my file system is corrupt.  When I run a system diagnostic, I am told there is a problem with one of my hard drives.  I have also tried to boot in safe mode, but the system hangs immediately after loading crcdisk.sys

Windows for home | Previous Windows versions | Windows update

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments No comments

57 answers

Sort by: Oldest
  1. Anonymous
    2013-02-27T05:44:33+00:00

    Hello, I am attempting to fix my wifes Dell Inspiron 1525 32-bit Vista Home Basic laptop.  She has been complaining that the computer doesn't shut down completely.  When she is forced to force the computer off, it no longer powers up again properly.

    When I first started looking into the problem, I noticed that the computer got hung up after attempting to start up in safe mode (this is what led me to this site).  I noticed that the computer got hung up at "crcdisk.sys" and after a relatively short time period, it appeared to reboot properly.  At that time, the computer seemed to be operational.  As I tried to shut down the computer down again, I was required to force it off and in turn no longer started up properly... vicious cycle.

    Once I got the computer up and running again, I was able to run "sfc /scannow" and got the below log of "corrupt files";

    https://www.dropbox.com/sh/mxivjt3q1p0b3r3/x3MtzAoSHh

    Please help :)

    Was this answer helpful?

    2 people found this answer helpful.
    0 comments No comments
  2. Anonymous
    2013-07-08T05:41:18+00:00

    Hi Everyone,

    I know this is years old now but I had the same thing hapen to me on my Windows 2008 R2 Server.

    I couldn't even boot from the Original 2008 DVD, It would get up to the Moving Graphic Windows Logo Screen and then the system would just restart at the Cold boot BIOS screen.  I checked all the BIOS settings and couldn't find anything that even looked like a problem.  (This machine is an old Dell 6400 server and the BIOS is really simple).

    Different from what the other users here have reported I have a RAID Array and ran a full diagnostic on the raid set and after hours of looking it couldn't find any problems.  At this stage I still thought it is probably a corrupted file which is why I tried to boot from the install disk.

    Just for fun I tried booting from an old XP disk into the setup routine and that worked OK.

    Of course I didn't actually install XP as I was still hoping to save the previous system.

    Again just for fun I popped out my SCSI card and re-seated it again.  The SCSI card doesn't run much more than the DVD drive these days as the RAID controller is completely separate.

    Much to my disbelief the machine booted and is now running perfectly.

    Who would have thought :)

    I hope this post helps someone else dealing with this obscure problem.

    Good Luck

    David

    Was this answer helpful?

    2 people found this answer helpful.
    0 comments No comments
  3. Anonymous
    2013-10-28T18:18:43+00:00

    Was able to restart Vista by using vista recovery disk that suggested system restore. Then sfc /scannow run without error.

    Was this answer helpful?

    2 people found this answer helpful.
    0 comments No comments
  4. Anonymous
    2014-06-08T21:28:46+00:00

    Are you nuts? WHY on earth would you give someone 20 things to do as a fix? That's not helpful at all. Plus you didn't read the askers post through because he's already tried at least 3 of the ones you put in there. Talk about overwhelming someone.

    Then you have the nerve to put "Most Helpful Reply" in giant letters at the top. Really? Because when you answer a question you're supposed to at least be know what you're talking about instead of throwing everything in, including the kitchen sink!

    I see it again and again in this forum. Some of you people think the most important thing is getting  help votes never mind that you really don't know the answer just throw in a bunch and you'll get what you want.

    Was this answer helpful?

    1 person found this answer helpful.
    0 comments No comments
  5. Anonymous
    2014-06-09T23:40:28+00:00

    Hi Pippin,

    Your not really flaming someone's post from four years ago are you?

    The "Most Helpful" bit is voted by other users not the poster. So someone must have liked it the post.

    The user who posted that response obviously spent a lot of time on it even if everything in there wasn't perfect.

    Sometimes in life it's better to say nothing at all if you can't find something positive to say. :)

    David

    Was this answer helpful?

    0 comments No comments