Windows couldn't automatically bind the IP protocol stack to the network adapter.

Anonymous
2009-10-27T03:01:51+00:00

This says I am connected to a wireless network when I am Wired. I get this error message. Need help quick

Windows for home | Previous Windows versions | Devices and drivers

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments
Answer accepted by question author
Anonymous
2009-10-28T02:14:13+00:00

Hello Bhawaii,

Welcome to Microsoft Answers Forum!

To assist you better I would like to ask you a question.

a)      Have you made any recent changes on your computer?

Step 1:

I would suggest you to run network diagnostic tool.

To perform this troubleshooting problem, please follow the steps below.

a)      Click on Start > Control Panel.

b)      Click on Network and Internet, and then click on Network and Sharing center.

c)      Under Network and Sharing centre, click on Troubleshoot Problem.

Step 2:

If this doesn’t helps. Then install the latest drivers for the network adaptor from the manufacturer’s website.

If this doesn’t fix the issue, then go ahead with the step 3.

Step 3:

Also I would suggest you to reset the network adaptor settings. Then follow the steps below

To reset the TCP/IP stack go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself:

http://support.microsoft.com/kb/299357

Disable the IP Helper service:

  1. Hold the Windows key and type R, enter "services.msc" (without the quotes) and press Enter
  2. Scroll down to the IP Helper service, right click on it and select Properties
  3. In the dropdown box that says "Automatic" or "Manual", set it to Disabled and then click on "Apply"
  4. Then click on "Stop" to stop the service from running in the current session
  5. Click OK to exit the dialog

Disable IPv6:

Try uninstalling IPv6 on all interfaces, removing any IPv6 virtual adapters, and resetting the TCP/IP stack. To remove IPv6, go into the properties for each network adapter and either uncheck the box next to the protocol "Internet Protocol version 6 (TCP/IPv6), that will disable it, or select it and click uninstall, which will remove it off the computer. Then go into device manager and remove any 4to6 adapters, WUN miniport adapters, or tunnel adapters.

NOTE: You should do this for each network connection.

Disable the DHCP Broadcast Flag: Link:

http://support.microsoft.com/default.aspx/kb/928233

Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:

http://support.microsoft.com/kb/322756

 (How to back up and restore the registry in Windows)

Windows Vista cannot obtain an IP address from certain routers or from certain non-Microsoft DHCP servers

To resolve this issue, disable the DHCP BROADCAST flag in Windows Vista. To do this, follow these steps:

  1. Click Start, type regedit in the Start Search box, and then click regedit in the Programs list.

If you are prompted for an administrator password or for confirmation, type your password, or click Continue.

  1. Locate and then click the following registry subkey:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces{GUID}

  1. In this registry path, click the (GUID) subkey that corresponds to the network adapter that is connected to the network.
  2. On the Edit menu, point to New, and then click DWORD (32-bit) Value.
  3. In the New Value #1 box, type DhcpConnEnableBcastFlagToggle, and then press ENTER.
  4. Right-click DhcpConnEnableBcastFlagToggle, and then click Modify.
  5. In the Value data box, type 1, and then click OK.
  6. Close Registry Editor.

By setting this registry key to 1, Windows Vista will first try to obtain an IP address by using the BROADCAST flag in DHCP Discover packets. If that fails, it will try to obtain an IP address without using the BROADCAST flag in DHCP Discover packets.

I hope that this information helps. Please get back to us if you have any more questions about this issue.

Thanks and Regards

Mir - Microsoft Answers Support   Engineer

Visit our Microsoft Answers Feedback Forum and let us know what you think

Was this answer helpful?

10+ people found this answer helpful.
0 comments

63 additional answers

Sort by: Newest
Most helpful Newest Oldest
  1. Anonymous
    2016-06-13T03:42:02+00:00

    This helped me. Thanks so much!

    Was this answer helpful?

    0 comments
  2. Anonymous
    2016-05-26T16:13:57+00:00

    After returning my TP-link L-WN823N wireless adapter to Walmart and buying the more expensive D-link DWA-130 adapter, I hit the same problem (Windows couldn't automatically bind the IP protocol stack to the network adapter). Undeterred, I used msconfig to close all non-Microsoft applications and attempted a reinstall of the adapter. In the attempt I noticed that Zone Alarm kept popping up and stopping changes. So, I completely uninstalled Zone Alarm, tried again and HOORAY! Henceforth I shall rely on just the Windows firewall!

    Was this answer helpful?

    2 people found this answer helpful.
    0 comments
  3. Anonymous
    2016-05-25T11:30:41+00:00

    Hi, I followed your instructions and I could resolve the problem. In my case was "AVG network filter driver." I unchecked it and the internet works.

    Many thanks...

    Was this answer helpful?

    0 comments
  4. Anonymous
    2016-04-09T00:51:35+00:00

    None of the above worked for me, but it turns out there was some third party software inserting itself into my adapter settings.

    Here's how I fixed it:

    Go to Control Panel> Network and Internet > Network Sharing Center

    Click 'Change adapter settings' in left pane.

    Right click your adapter. Select 'properties'.

    There will be a box headed 'This connection uses the following items.'

    Uncheck anything that looks like it was installed by a third party (AVG, Avast, ZoneAlarm). In my case the culprit was 'HTC NDIS Protocol Driver' which was installed by my cell phone software (HTC). Since it might not be obvious what to uncheck, here is what I currently have checked in my working system that should not cause a problem:

    KEEP THESE CHECKED:

    Client for Microsoft Networks

    QoS packet scheduler

    File and Printer Sharing

    Internet Protocol v6

    Internet Protocal v4

    Link-Layer Topology Discovery Mapper I/O driver

    Link-Layer Topology Discovery Reminder

    Uncheck everything else.

    Go back to the Network and Sharing menu, disable and re-enable the adapter.  That should work.

    Perfect, thank you so much, you have no idea how much trouble you have saved me. You are an absolute star. Thank you thank you thank you.

    Mike.

    Was this answer helpful?

    1 person found this answer helpful.
    0 comments