Laptop hangs up at Classpnp.sys file.

Anonymous

So I installed Windows 7 the other night on my laptop. I did the driver updates and installed Norton. I also installed Office 2007. Then I shut it down for the night. The next day I turned it back on to install a few more things. A friend recommended that I install Ad-Aware, so I did, and ran it. I've used it on a few of my machines before with no problems. I installed a couple more programs (SANDRA & CPU-ID) then I shut it down for the night. It stalled on shutdown. I didn't think anything about it and after about 20 minutes I did the power-off. I started it up the next day and it now hangs at the starting windows screen. I've tried the following with all the same results:

System repair - hangs at the repair screen
Start normally - hangs at the starting windows screen
Start in safe mode - hangs at the classpnp.sys file
Start in safe mode with command prompt - hangs at the classpnp.sys file
start in safe mode with networking - hangs at the classpnp.sys file

I've even tried to put in the windows 7 disc back in to do a re-install and it hangs at the starting windows screen.

It seems like no matter what I try I get the hang up at the windows starting screen.

Someone help, please!!!

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments

Answer accepted by question author

Anonymous

So the other night I tried a few more things with all the same results. Here's what I tried:

I bought a second gig of ram, so I tried swopping out one stick, then the other - same results.
I bought a hard drive enclosure, removed the hard drive, formatted it with another computer, made sure I could save things to it, re-installed hard drive, booted from CD - same results.
I bought a brand new hard drive, installed it, booted from CD - same results.
Put old hard drive back in with both sticks of ram - same results.

After reviewing a few things, I found that when Windows gets to the "Starting Windows" screen, it's checking your hardware to make sure that things are OK. Well, my hard drive, RAM, CD Drive, and Video Card are OK (I get all the right video stuff), so there's only a couple of things left, and one is the motherboard. So, I believe that there is a hardware issue that is not allowing Win7 to completely load.

0 comments

Answer accepted by question author

Anonymous

Go into your bios and check the hard drive configuration. Once I reverted back to IDE the system booted as normal. You may have to do the opposite!!!

At all times my system hung at classpnp.sys as advertised. Let me know if this fixed

Macbionik.com

0 comments

135 additional answers

Anonymous

2010-12-30T12:05:52+00:00

Hi I had the exact same problem after installing CPU-ID. I suspected that this was the problem and after reading your post I'm sure it is. My computer also stalls out on classpnp.sys file but if I just let the computer run it finally boots into safe mode. I'd would try and uninstall that CPU-ID ____...

mmcat
Was this answer helpful?

0 comments No comments
Anonymous

2010-12-29T06:47:10+00:00

*Bows Down*

OMG YES!!! You have no idea how frustrating the past 2 days have been. I can now fluently communicated in DOS, but this seemed to fix it!
Was this answer helpful?

0 comments No comments
Anonymous

2010-12-18T02:14:02+00:00

i listened to macbionik and went into bios and changed my sata controller from ahci to compatible and it seems to have started doing stuff. I tryed safe mode and it would just hang on Classpnp.sys. Before that I was having the exact same problems everyone else was having on here. I even swapped out drives and that didn't help. I suggest going into bios and switching it or return it to default then reboot. Then try the repair.
Was this answer helpful?

0 comments No comments