Event log shows event 11 atapi: The driver detected a controller error on \Device\Ide\IdePort1

Anonymous
2009-11-06T21:22:48+00:00

Intermittent hangs. Event log shows event 11 atapi: The driver detected a controller error on \Device\Ide\IdePort1. How do I find this device? Is this probably a hardware problem?

I am investigating intermittent hangs, where my cursor becomes an hourglass and the system will not even respond to ctrl-alt-del.  In the event log, I find

  Event 11 atapi : The driver detected a controller error on \Device\Ide\IdePort1.

How do i determine which physical device(s) this is associated with?  Does this indicate a hardware problem, or might driver or firmware be the source?The system has been running fine for a couple years.  I am not aware of any software changes that have occurred recently, though I did have to forcibly remove and reinstall iTunes a little while ago.

I have run SMART checks on all drives and run some diagnostics.  I ran chkdsk on the one that I thought was the culprit, but no errors.

Just in case it was a memory-related hang, I tried to use the microsoft memory diagnostic on floppy, but it wouldn't write to the floppy (even though I could format it and copy files freely).

Windows for home | Previous Windows versions | Devices and drivers

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments
Answer accepted by question author
Anonymous
2010-05-31T12:13:08+00:00

Hi

Go into your setup and look at what drive is adressed at each port; 1,2,3,4....

Then go to Device Manager and look how many SATA controller you have and how many ports for each, then start count from 0 for IdePort0, 1, 2, etc. for each SATA controller, so if you got 4 ports for each SATA controler, here it is how you got to count:

drive 1 - IdePort0, drive 2 - IdePort1, drive 3 - IdePort2 and drive 4 - IdePort3 in sequence

I hope it helps

Was this answer helpful?

40+ people found this answer helpful.
0 comments

43 additional answers

Sort by: Oldest
Most helpful Newest Oldest
  1. Anonymous
    2009-11-07T20:30:57+00:00

    Hi Paul,

    You may try the following steps.

    1.      Right-click My Computer, and then click Manage.

    2.      Double-click System Tools in the right pane, and then double-click Device Manager.

    3.      Double-click IDE ATA/ATAPI Controller in the right pane, and then double-click the appropriate controller.

    4.      On the Advanced Settings tab, click PIO Only in the Transfer Mode box.

    5.      Click OK, close the Computer Management window, and then reboot the computer.

    ****Ide cables are for the hard drive or the cd/dvd drive. Hence I would suggest you to unplug the cables and re-plug the cables or change it if required.

    Disclaimer: Unplugging the cables can cause serious problems that may prevent your computer from booting properly. Making changes are at your own risk.

    Thanks and Regards,

    Bindu S - Microsoft Support

    Visit our Microsoft Answers Feedback Forumand let us know what you think.

    Was this answer helpful?

    1 person found this answer helpful.
    0 comments
  2. Anonymous
    2009-11-11T16:40:15+00:00

    Is 'IdePort1' the same as 'ATA Channel 1' in device manager?  I have ATA Channel 0 and ATA Channel 1.  On Channel 1, I have device target ID 0 and target ID 1.  How do I match this to the information in the alert \Device\Ide\IdePort1 ?

    For these devices, there isnt an option for PIO, but I can turn off DMA.

    Also, I experienced two more hangs yesterday without any new alerts in the System Log.  Is there anywhere else I should be looking?

    Thanks,

    Paul

    Was this answer helpful?

    0 comments
  3. Anonymous
    2009-11-21T20:22:33+00:00

    Bump.   Any additional advice?

    Was this answer helpful?

    0 comments
  4. Anonymous
    2009-11-25T13:04:33+00:00

    Hi PaulbAustin,

    Sorry for the delayed response.

    Event ID 11 is a more serious error than an I/O time-out. This error could be a result of a bad or corrupted device driver, a hardware problem, a malfunctioning device, poor cabling, or termination issues. This is an error occurring within the driver or hardware itself, not the cluster software. 

    I would suggest you to disable the cd/dvd drive from the device manager and check if the issue still persists.

    1. Click start
    2. Type devmgmt.msc in Start Search and press enter.
    3. In the device manager expand cd/dvd rom drive
    4. Right click on the driver and choose disable.

    If this works it can be an issue with the drive itself. You might have to replace it.

    Also try the cd/dvd rom drive on a different computer and check if the issue persists.

    Check the version of the SCSI controller BIOS and the device firmware revision. If the issue still persists you migth have to contact your computer  manufacturer for the latest updates. 

    Regards,

    Bindu S - Microsoft Support

    Visit our Microsoft Answers Feedback Forumand let us know what you think

    Was this answer helpful?

    0 comments